Saeco Coffee machine Service Manual download pdf (Page 7)

Drainage

Direct the steam/hot water dispensing tube (5)

over the drip tray (2).

Place a cup or another suitable container under

the dispensing tube, then turn the steam/hot water

selection knob (6) counterclockwise.

The pump automatically starts.

Wait until a regular water jet is obtained, then

close the knob. The machine is now drained.

Important: It is advisable to drain the machine

before the first start, after a prolonged use or

whenever the water tank has been completely

emptied.

Furthermore, should temperature

or water tank

warning lights blink, drain the machine.

The machine is ready for use as soon as the

temperature light is on.

Programming the machine

27 To enter the programming mode, turn the

machine off with the main switch.

Press steam

, espresso coffee and the

main switch at the same time.

Release the buttons.

Water hardness adjustment

In order to adjust the water hardness, it is neces-

sary to test the water using the strip supplied with

the machine.

Dip the strip into the water for a second, shake off

excess water gently, wait approx. 1 minute and

read the result.

The tall coffee button

allows a water hardness

adjustment from 1 to 4.

Each time the key is pressed, the value increases

by 1.

Never fill the coffee bean container

with other products! (They might

damage the machine!)

Before filling the container with coffee

beans, make sure the pre-ground

coffee container is closed to prevent coffee grains

from falling into it (they might damage the ma-

chine).

Remove the water tank (8) from the machine,

remove its cover (9) and fill it with cold water

(approx. 2.4 l).

A valve on the tank bottom prevents water from

escaping.

Before installing the water tank in the machine,

make sure the coffee bean container cover is

properly fitted.

26 Install the water tank, slightly pressing over it

to fit the valve which will open automatically.

Replace the cover on the tank.

Do not fill the tank with an excessive

quantity of water.

Always fill the tank with fresh water: hot

water as well as other fluids

might damage the tank.

Do not switch on the machine if the

water tank is empty: always make

sure there is enough water in the tank!

Connect the plug to the socket and press the main

switch.

When the switch is turned on (green colour), the

electronic circuit carries out a self-diagnosis. This

phase could make some noise.

DRAINAGE

RECOMMENDATIONS

As soon as value 4 has been reached, the counter

resets and restarts from 1.

As far as lime scale values are concerned, see

page 37, points 45-48.

Pre-Grinding

The coffee grinder is activated by pressing the

button of the heating plate

When this button lights up, the coffee grinder has

been activated.

Grinding occurs every time the doser is empty,

thus a ground coffee portion is always ready in the

doser, saving time.

Pre-Infusion

The regular coffee button

activates or

disactivates the dispensing of coffee, as shown by

the lit button.

As soon as the coffee has been moistened, the

pump stops for two seconds. Then the brewing

cycle continues.

Coffe dosage adjustment

28 Adjustment lever (19) allows the selection of

the coffee quantity, from 6 to 9 grams.

Open the service door (15) and place the

adjustment lever (19) in the desired position.

Note: Opening the service door causes the

machine to stop automatically. Close the door to

restart the machine.

Coffee dosage must not be changed

frequently, otherwise the coffee dis-

penser may get damaged, thus spoiling the

quality of coffee.

Recommendations

Test

If the machine has not been used for a prolonged

period, it is advisable for hygienic reasons to run

a rinse cycle through the machine.

Place a cup under the dispensing tube (5) and

operate the steam/hot water knob (6). Fill a cup

with water.

Preheating cups

Cups may be preheated by placing them on the

heating plate.

Temperature warning light

When connecting the machine, the green warn-

ing light will light permanently after approx. two

minutes, showing the machine is ready to be

used.

Empty coffee bean container warning

light

When this led is on, the coffee grinder stops.

Fill the container with coffee bean and restart the

cycle.

Empty water tank warning light

An empty water tank causes the cycle to stop

automatically.

Fill the tank with water. It is of the utmost

importance to drain the circuit before restarting the

machine.

It is not possible to start programming without

carrying out the drainage.

When restarting the machine, make sure the red

warning light is not blinking or is off.

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Saeco Coffee machine Service Manual Page 7

Comments to this Manuals

Related products and manuals for Coffee makers Saeco Coffee machine